Item No.:1/10  nitro 4 wheel drifting rc car model buggy

Description: rc hobby, nitro rc racing car model

AM27 transmitter with LED Screen, 1800ham battery

Speed: 80-90 KM / hour

Play time: 15 minutes

Engine level: 15cxp,18cxp

4pc / carton

Item size: 41*25*15.5cm

Carton size: 52*26*18cm

Packing size: 59*56*63.5cm

G.W/N.W: 26.8/21kg

Specification:

• 1/10 Scale Nitro 4 wheel drifting rc car model buggy
• Pre-assembled Chassis,3mm Aluminum Main Chassis
• Shaft Drive 4Wheel Drifting System
• Disc Brake System,Ex-factory Set 15/18t Power Engine
• Composite Long Suspension Arms,Front&Rear Oil-filled Long Shocksie
• 755cc Fuel Tank
• Aluminum Exhaust Pipe,54/49T Gear Two Speed Gear Box,Or 54T Gear Center Differential
• Front&Rear Differential With Added Rigidity Gear
• Steering Servo With Metal Gear
• Impact Absorbing Front&Rear Bumper
• Racing Wheels&Tires
• Front&Rear Self-adjustable rocker4 Wheel Drive
• 2 Speed Automatic Transmission
• Powerful 15 engine equipped with slide carburetor and pull-starter.
•  Four wheel drive system with shaft drive.
• Suspension: Four wheel independent double wishbone system 

Function:

Go forward&reverse, turn left&right,4x4 full time drifting.

Dimensions of vehicle:

Length: 410mm 

Height: 155mm

Width: 250mm 

Track: 185mm

Wheelbase: 275mm

Tyres: 86 x 32mm(F)/86 x 40mm(R)

Ground clearance: 25.5mm

Gear ratio: 5.75:1(H)/8.55:1(L)

Weight: 1850g

Packing:

-HL Lightning Brushless Version 1/10 racing car

-3 Channel LCD screen Computerized Radio Transmitter
-User Manuals.
-7.2V,1800mAh battery
 4pc / carton

Item size: 41*25*15.5cm

Carton size: 52*26*18cm

Packing size: 59*56*63.5cm

G.W/N.W: 26.8/21kg

Features:

1) the process of cleaning before driving your car: For cleaning the engine,1-2 tank oil's use is a standard, and then run your car slowly to run out of another 1-2 tank oil, all ways down, the cleaning work is over, the car can run normally

2) turning on the transmitter and the receiver: Extend the antenna of the transmitter and the receiver, and then switch on the transmitter and the receiver in succession;

While switching on the receiver, make sure the carburetor is at the neutral position

3) fill the fuel: Fill the special model's fuel, and mix the gas and the lubricating oil, the rate of the gas to the lubricating oil is 25:1; close the fuel tank's cover and fasten it after it after filling the fuel

4) starting the engine: Push the front valve several times until securely streaming out oil; shut down the wind gate, and turn the accelerograph to the position that

Spaces 1/4-1/3 place of opening; pull the pulling-start rod until engine send out sound of start to start engine adjust the wind gate to the place which spaces 1/4 position of opening position; pull the pulling-started rod quickly; start engine several minutes to pre-warm

5) stop the engine: The engine will immediately stop running as long as you press the stall switch of the engine, please refer to the instruction manual(g230 rc) for more details

6) 2-channel transmitter system: The servo must be set at the center position before installation, to set the neutral turn on the transmitter and receiver, set the trim tabs in the center position, and turn off the receiver and transmitter in succession, the

Servo will be in the proper neutral position for installation