Item No.:1/10 big feet nitro 4WD on road rc racing car model truck

Description: nitro rc racing car model truck

AM27 transmitter with LED Screen, 1800ham battery

Speed: 80-90 KM / hour

Play time: 15 minutes

Engine level: 15cxp,18cxp

4pc / carton

Item size: 40*31*21cm

Carton size: 53*26*22cm

Packing size: 76.5*56*52cm

G.W/N.W: 20/18kg

Specification:

1/10 Scale Nitro 4WD rc  Racing car model Truck

• 2 Speed Automatic Gearbox with ALL Metal Gears
• Reverse Gear operated by 3 Channel Transmitter (included)
• Manual Select High and Low Range
• 3 Channel Pistol Grip Radio Factory Installed
• 4 Servos including 2 Metal Geared High Torque Steering Servos
• Portable Electric Rotor Starter and NiCad Battery
• 1800mah NiCad 6 Volt Rechargeable Receiver Battery
• NiCad Battery Charger
• Tough Countersunk Anodized Dual Level Aluminium Chassis with Polycarbonate Bracing
• High Volume Element Air Cleaner
• Anodized Aluminium Fuel Filter

• Race Tuned Exhaust
• 4 Wheel Drive, on road racing car model truck
• Front and Rear Ball Raced Viscous Differentials with Metal Bevel Gears
• Oversize Pressurised Fuel Tank
• Full 4 Wheel A-Arm 100% independent Adjustable Suspension
• Factory Glued Tyres with Inserts on Dish Style Racing Wheels
• Oversized Race Aluminium Oil Filled Adjustable Shock Absorbers
• Powerful Twin Disc Braking with Replaceable Pads
• Factory Installed Servo Savers
Chassis Type: Twin Plate Braced Anodized Aluminium

Suspension: Four wheel independent double wishbone system 

Function:

Go forward&reverse, turn left&right,4x4 full time drifting.

Packing:

-HL Lightning Brushless Version 1/10 racing truck

-3 Channel LCD screen Computerized Radio Transmitter
-User Manuals.
-7.2V,1800mAh battery

4pc / carton

Item size: 40*31*21cm

Carton size: 53*26*22cm

Packing size: 76.5*56*52cm

G.W/N.W: 20/18kg

Features:

1) the process of cleaning before driving your car: For cleaning the engine,1-2 tank oil's use is a standard, and then run your car slowly to run out of another 1-2 tank oil, all ways down, the cleaning work is over, the car can run normally

2) turning on the transmitter and the receiver: Extend the antenna of the transmitter and the receiver, and then switch on the transmitter and the receiver in succession;

While switching on the receiver, make sure the carburetor is at the neutral position

3) fill the fuel: Fill the special model's fuel, and mix the gas and the lubricating oil, the rate of the gas to the lubricating oil is 25:1; close the fuel tank's cover and fasten it after it after filling the fuel.

4) starting the engine: Push the front valve several times until securely streaming out oil; shut down the wind gate, and turn the accelerograph to the position thatSpaces 1/4-1/3 place of opening; pull the pulling-start rod until engine send out sound of start to start engine adjust the wind gate to the place which spaces 1/4 position of opening position; pull the pulling-started rod quickly; start engine several minutes to pre-warm.

5) stop the engine: The engine will immediately stop running as long as you press the stall switch of the engine, please refer to the instruction manual(g230 rc) for more details

6) 2-channel transmitter system: The servo must be set at the center position before installation, to set the neutral turn on the transmitter and receiver, set the trim tabs in the center position, and turn off the receiver and transmitter in succession, theServo will be in the proper neutral position for installation.